Murexide
Hazard to Self
Posts: 51
Registered: 1-12-2018
Member Is Offline
|
|
Storage containers
Hello all,
What do you store your solid chems in?
Many eBay chemicals come in standard zip lock bags (probably for cost reasons). So far I’ve kept them in here without too many problems, but it
seems quite messy altogether. (Even iodine came inside a zip lock bag inside an aluminium (!) pouch, I immediately moved this to triple bagged /
double vialed container)
But I’ve come across some cheap reagent plastic bottles that are about $1/each (less in bulk), quite tempting to move the many chems into these
bottles.
Do you keep these bottles on hand for general use? How much does it generally cost you?
Also, do disposable plastic spoons work for scooping chemicals out (could be PET or Other, not quite sure)? These seem to be very cheap (couple
dollars for hundreds) and much less of a hassle than using chemical scoops, then having to dry them (using a tissue deposits small amounts of paper
everywhere!)
|
|
|
karlos³
International Hazard
Posts: 1520
Registered: 10-1-2011
Location: yes!
Member Is Offline
Mood: oxazolidinic 8)
|
|
Either in PP containers or glass with a PP screw lid on(like with, for example, iodine).
I just use old storage containers from which I used the original content up, never a good idea to throw the empty ones away.
Same with liquid chemicals, I keep most of the amber glass bottles I used up for further storage of self produced things.
PP spoons work well, PET I would imagine not so much.
I use these things for anything metal won't do well with.
|
|
|
Dr.Bob
International Hazard
Posts: 2757
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: Mildly disgruntled scientist
|
|
Many containers work well, almost all are better than plastic bags. I like glass, as that tends to keep out water better, but even that can fail is
the lid is not a tight seal. I have some chemicals in Qorpak type bottles that are 40 years old, and most are still fine. But I have used a
variety of reused bottles. Cheap plastic bottles do tend to get very brittle over time, I recently cleaned up some old chemicals and the ones in old,
thin, white bottles were very brittle, some were cracked or just fell apart when I tried to handle them. But the thicker ones did fine. Old plastic
bags tend to just get weak quickly, many of the chemicals in plastic bags were leaking or very weak or very wet. So I would not store anytime that
might be hazardous in plastic. It is fine for Na2HCO3, CaCO3, and other harmless salts, but not for heavy metals, bases, acids, etc.
I have some various plastic containers for $1 each, as well as a variety of glass bottle for only $2 or less. Not as much variety as before, but I
can likely find something good for most sizes. And many have PTFE liners in Green phenolic caps, which will last forever, and resist most
everything. Plus you can get glass vials from 4 ml to 40 ml pretty cheaply, and they also work well for small samples, and are easy to store.
|
|
|
PirateDocBrown
National Hazard
Posts: 570
Registered: 27-11-2016
Location: Minnesota
Member Is Offline
Mood: No Mood
|
|
The changes in packaging chems is sometimes a bit disconcerting for old hands.
I'm used to liquids in nice Boston rounds, and solids in Blakes, Packers, or even French Squares.
Phlogiston manufacturer/supplier.
For all your phlogiston needs.
|
|
|
CharlieA
National Hazard
Posts: 646
Registered: 11-8-2015
Location: Missouri, USA
Member Is Offline
Mood: No Mood
|
|
For most solids, I use peanut butter jars (PETE plastic). (I eat a lot of peanut butter.) I prefer glass. For wide-mouth glass jars, I generally
re-use food containers. I have purchased narrow mouth glass bottles, both amber and clear, including some with PTFE lined caps.
|
|
|
Murexide
Hazard to Self
Posts: 51
Registered: 1-12-2018
Member Is Offline
|
|
So it seems like the consensus is to move the reagents to bottles. I guess I'll explore the options and make that happen.
@Dr.Bob Thank you for your offer with the bottles and vials. Currently most of my chemicals are not very hazardous, but if I have to store anything
dangerous / needs to be sealed very well, I'll be sure to consider it.
As for the spoons, I did some research and it turns out they're either made of polystyrene or polypropylene. Looking at a chemical compatibility chart
they're both fine for all the solids I've searched up so that's quite good.
For the bottles, I also made some labels. I'm thinking of printing them (using inkjet printer) on printable vinyl adhesive, it'll last longer and
won't fall off. Anyone experimented with this?
|
|
|
teodor
National Hazard
Posts: 924
Registered: 28-6-2019
Location: Netherlands
Member Is Offline
|
|
I often use this type of containers. Costs 50-70 eurocents each. In the Netherlands you can buy them in Action shop.
|
|
|
PirateDocBrown
National Hazard
Posts: 570
Registered: 27-11-2016
Location: Minnesota
Member Is Offline
Mood: No Mood
|
|
If it's non-corrosive, the easiest and cheapest is usually Mason jars.
I also often reuse old food jars, even plastic mayonaise jars (for very inert compounds, like sodium bicarbonate).
cylindrical olive jars wrok well for many items, or low- profile wide mouths, like pimientos often come in.
Naturally, for more corrosive compounds, more inert containers are needed.
Phlogiston manufacturer/supplier.
For all your phlogiston needs.
|
|
|
hodges
National Hazard
Posts: 525
Registered: 17-12-2003
Location: Midwest
Member Is Offline
|
|
I bought standard chemical storage containers (amber glass bottles, plastic bottles, small plastic jars) from homesciencetools.com (US). Not too
expensive.
I make up standard concentrations of acids from commercial products such as muriatic acid and rooto drain cleaner, and store them in amber glass
bottles. Good to have, for example, 3M acid solutions for most experiments, vs. the 12-18M raw product. A bit safer to handle on a routine basis as
well. I have 3M NaOH solution in a plastic bottle designed for chemical storage. Salts I store in the plastic chemical storage jars.
I did try ordering "ordinary" plastic storage jars on eBay, but they were not suitable even for storing salts (not at all airtight). I have used old
plastic jars that previously contained vitamins, prescription medicines, and bullion cubes before (obviously, remove the original labels), and they
are better than "ordinary" plastic jars from eBay but are not completely airtight.
|
|
|
Arthur Dent
National Hazard
Posts: 553
Registered: 22-10-2010
Member Is Offline
Mood: entropic
|
|
I usually use 1l growlers from breweries, and as a bonus, they come with the nice bakelite caps with a protruding plastic insert inside. Excellent for
solvents, and acids, although HCl and HNO3 are in special hi-end lab bottles with heavy PTFE caps.
For dry chemicals, the nice square jars with a colored metal cap at the dollar store are just perfect. One of my family member is a pharmacist and
provides me on occasion with empty pill bottles, really nice, thick plastic bottles with a wide mouth.
I recently purchased a bit of KMnO3, which came in thick, vacuum-sealed plastic bags. I put the bags unopened in a glass jar, since it appears to keep
the powder perfectly dry. Hope the plastic bags will not degrade. 
--- Art is making something out of nothing and selling it. - Frank Zappa ---
|
|
|
karlos³
International Hazard
Posts: 1520
Registered: 10-1-2011
Location: yes!
Member Is Offline
Mood: oxazolidinic 8)
|
|
KMnO3, wow 
Did not know that exists.... no honestly, sorry, am just kidding regarding the typo 
|
|
|
Arthur Dent
National Hazard
Posts: 553
Registered: 22-10-2010
Member Is Offline
Mood: entropic
|
|
Oh. Uh. Argh. KMnO4... my finger slipped... honest! LOL
--- Art is making something out of nothing and selling it. - Frank Zappa ---
|
|
|
Abromination
Hazard to Others
Posts: 432
Registered: 10-7-2018
Location: Alaska
Member Is Offline
Mood: 1,4 tar
|
|
I like to use jars like the ones teodor shows in his picture and PP or HDPE pill bottles. I usually prefer glass if possible.
List of materials made by ScienceMadness.org users:
https://docs.google.com/spreadsheets/d/1nmJ8uq-h4IkXPxD5svnT...
--------------------------------
Elements Collected: H, Li, B, C, N, O, Mg, Al, Si, P, S, Fe, Ni, Cu, Zn, Ag, I, Au, Pb, Bi, Am
Last Acquired: B
Next: Na
-------------- |
|
|
rockyit98
Hazard to Others
Posts: 283
Registered: 12-4-2019
Location: The Known Universe
Member Is Offline
Mood: no mood is a good mood
|
|
sometimes you can find PVC containers. they are awesome because hey resist UV radiation unlike PP, doesn't react with HNO3 like PP or LDPE, can handle
NaOH.but be aware some organic solvent can dissolve it like in PVC glue eg: Acetone , Cyclohexanone and Methyl ethyl ketone.
"A mind is a terrible thing to lose"-Meisner
|
|
|
Dr.Bob
International Hazard
Posts: 2757
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: Mildly disgruntled scientist
|
|
I would avoid PVC for much in the lab, it is not only not resistant to most organics, but it becomes very brittle with time, and will eventually just
break. I just recently cleaned up some messes due to exactly that. But I have glass bottles of chemicals that are 40+ years old that look like
new.
|
|
|
CharlieA
National Hazard
Posts: 646
Registered: 11-8-2015
Location: Missouri, USA
Member Is Offline
Mood: No Mood
|
|
I agree with Abromination and Dr. Bob: go with glass. I also use HDPE/LDPE and PP containers, but I haven't found any pill containers other than PETE,
which I use mainly for dry samples.
|
|
|
rockyit98
Hazard to Others
Posts: 283
Registered: 12-4-2019
Location: The Known Universe
Member Is Offline
Mood: no mood is a good mood
|
|
jam jars is ok for dry chemicals. steel lids will corrode if got wet.i don't have a 3D printer but can any one tried to print lids with ABS? will it
work? i store super glue tube in one with calcium carbide piece wraparound tissue paper as a water absorber. it seals well and i can use 3g super glue
for months.
"A mind is a terrible thing to lose"-Meisner
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
