agorot
Hazard to Self
Posts: 73
Registered: 25-1-2010
Location: too fed-o-phobic to say :D
Member Is Offline
Mood: like an activated complex
|
|
Cleaning carbon dust from the bottom of a flask
Hey everyone
I made some KClO3 the other day with carbon electrodes. To make a long story short, I now have some very fine carbon particles at the bottom of a 500
mL RBF that my fingers can't reach, nor can a paper towel. It obviously won't dissolve in water. Anyone have any ideas on how to clean it out? It's
just settled to the bottom over a long period of time and it won't come out.
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
A flask cleaning brush?
Try putting some water, a drop of detergent, and a bit of course sand into the flask, and swirling it for awhile.
|
|
|
woelen
Super Administrator
Posts: 8012
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Another option is to put some coarse sand and water in the flask and then shake.
|
|
|
The WiZard is In
International Hazard
Posts: 1617
Registered: 3-4-2010
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by agorot  | Hey everyone
I made some KClO3 the other day with carbon electrodes. To make a long story short, I now have some very fine carbon particles at the bottom of a 500
mL RBF that my fingers can't reach, nor can a paper towel. It obviously won't dissolve in water. Anyone have any ideas on how to clean it out? It's
just settled to the bottom over a long period of time and it won't come out.
|
-----------
Nitric acid perhaps. Or oxidize it into graphic acid. Details in
among others — Mellor's 16-volume opus. 5:828 &ff
Heat it with some of your chlorate and report back.
[Edited on 1-6-2010 by The WiZard is In]
|
|
|
hissingnoise
International Hazard
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
| Quote: | | Heat it with some of your chlorate and report back. |
Report! Yeah!
But if you want to go technical, get one of your artists hogshair brushes and scrub the inverted flask so that the residue falls out. . .
|
|
|
zed
International Hazard
Posts: 2283
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Turn the flask upside down. Create a static charge on the flask. A Van DeGraff generator should do that nicely. Provided there is no adhesive
material present, the flask and the carbon particles, both bearing the same charge, will repel each other.
Shazzam. The particles will fall off, and out of the flask. Maybe.
Another possibility, involves heating the flask fairly hot over a bunsen burner, and sweeping the bottom of the flask with a stream of pure oxygen.
The carbon particles will be oxidized to CO2, and you will be spared the labor of scrubbing.
|
|
|
kmno4
International Hazard
Posts: 1497
Registered: 1-6-2005
Location: Silly, stupid country
Member Is Offline
Mood: No Mood
|
|
Recently I had similar problem (residue after PS pyrolysis).
And one more time, warm H2SO4+K2Cr2O7 (or any chromate, CrO3...) mixture did not disappoint me.
In case of C particles, oxidation may take a few hours but always works.
|
|
|
rrkss
Hazard to Others
Posts: 193
Registered: 18-12-2009
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by kmno4 | Recently I had similar problem (residue after PS pyrolysis).
And one more time, warm H2SO4+K2Cr2O7 (or any chromate, CrO3...) mixture did not disappoint me.
In case of C particles, oxidation may take a few hours but always works. |
Chromic acid is toxic, carcinogenic, pain in the ass to dispose of legally and not needed for most cases. Why not start with something mild like
scrubbing with a brush, and a mild nonscratching abrasive soap. If that does not work, a soak in a solution of KOH + Ethanol usually does the trick.
[Edited on 6-2-10 by rrkss]
|
|
|
agorot
Hazard to Self
Posts: 73
Registered: 25-1-2010
Location: too fed-o-phobic to say :D
Member Is Offline
Mood: like an activated complex
|
|
you guys are terrible 
and don't you think I would have already tried a brush?
I'll see how the sand works.
|
|
|
kmno4
International Hazard
Posts: 1497
Registered: 1-6-2005
Location: Silly, stupid country
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by rrkss | | Quote: Originally posted by kmno4 | Recently I had similar problem (residue after PS pyrolysis).
And one more time, warm H2SO4+K2Cr2O7 (or any chromate, CrO3...) mixture did not disappoint me.
In case of C particles, oxidation may take a few hours but always works. |
Chromic acid is toxic, carcinogenic, pain in the ass to dispose of legally and not needed for most cases. |
As far as I know non-carcinogenic is only water and air.
Other substances are or will be recognized as carcinogenes.
Chromic mixture has been well known and used for many years. It is cheap and easy to prepare. Its purpose are mainly carbonaceous impurities.
It can be a pain in the ass only in if used rectally..... 
|
|
|
psychokinetic
National Hazard
Posts: 558
Registered: 30-8-2009
Location: Nouveau Sheepelande.
Member Is Offline
Mood: Constantly missing equilibrium
|
|
With a spoon.
And a lot of violence.
“If Edison had a needle to find in a haystack, he would proceed at once with the diligence of the bee to examine straw after straw until he found
the object of his search.
I was a sorry witness of such doings, knowing that a little theory and calculation would have saved him ninety per cent of his labor.”
-Tesla
|
|
|
mr.crow
National Hazard
Posts: 884
Registered: 9-9-2009
Location: Canada
Member Is Offline
Mood: 0xFF
|
|
Piranha solution
Maybe you can neutralize your waste chromic acid with alcohol (carefully!) so you get Cr3+
Cr free cleaners use sodium persulfate and H2SO4. You can get ammonuium persulfate for etching circuit boards. I'm not sure if this is effective.
Double, double toil and trouble; Fire burn, and caldron bubble
|
|
|
zed
International Hazard
Posts: 2283
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Ozone?
|
|
|
Mr. Wizard
International Hazard
Posts: 1042
Registered: 30-3-2003
Member Is Offline
Mood: No Mood
|
|
Use a slow flow of O2 into the flask and start warming the spots with carbon on them, with a flame from a Bunsen burner This will work unless the dark
material you think is carbon, is something else.
|
|
|
Jimmymajesty
Hazard to Others
Posts: 153
Registered: 9-7-2009
Member Is Offline
Mood: No Mood
|
|
A Van DeGraff generator... Dude.. you can not be serious about that!
Just heat the flask with cc H2SO4, It always worked for me to remove carbon particles, char, tar etc.. from everything (except from porous surfaces
like Al2O3) chromium compounds are not necessary, and I second that their use is a PITA
|
|
|
Lambda-Eyde
National Hazard
Posts: 860
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
I second this! I had a 250 ml round bottom flask with quite a lot of tar in it that would not go away. I tried to clean it with
HNO<sub>3</sub>, then NaOH. Neither was effective. I didn't have any brushes that would reach the tar, so brushing was out of the
question.
However, adding some coarse marble (calcium carbonate), a few drops of detergent and shaking made it shine like never before.
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
Actually you're thirding it, I suggested that in my first reply, as well as using a drop of detergent along with the sand and water as that seems to
help wet condensed organic films clinging to glass in my experience.
Still, a few good flask brushes are worthwhile investments.
For thicker deposits, refluxing a cheap high boiling organic solvent such as kerosene can help, I've used it after cracking polystyrene. After
refluxing the solvent for awhile pour the still hot solvent off, repeat if needed. Finish with some more conventional cleaning route - brush or sand.
|
|
|
puppycock
Harmless
Posts: 11
Registered: 1-4-2010
Member Is Offline
Mood: No Mood
|
|
I suggest using piranha solution, I left an organic solution drying unattended for too long and decomposed leaving a bunch of elemental carbon stuck
to my round flask and it was perfectly clean after 5 minutos of heating.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
