The other day in lab I was cleaning my sieve with an ultrasound bath, when I noticed that pressing the sieve against water created an air bag
underneath which didn't allow the sieve to sink, even though air should have supposedly escaped from the several holes (large 400um) of the grit.
I painted what I did:
The sieve would only sink if I inclined it by a certain angle, in order to allow water to enter from the bottom sides, but if I pressed it by
maintaining the sieve parallel to the water surface, it wouldn't sink for shit.
Something tells me that this has to do with the capillar force that keeps water well "stuck" to the small holes (the sieve was wet afterall), creating
a film of water that doesn't let air pass, no matter how much I pressed.
... or am I totally off with my assumption? Why does this happen? (Just random things that occasionally happen and that are enough to amaze an
ignorant mind)hissingnoise - 20-1-2016 at 06:40
Quote:
. . . it wouldn't sink for shit.
You could heat the water slowly and see what happens . . . ?
Texium - 20-1-2016 at 06:47
Perhaps try it again with a completely dry sieve and see if you get the same results.hissingnoise - 20-1-2016 at 07:26
Heating the water will reduce its viscosity, but now I'm unsure if it's viscosity
trapping the air or is it surface tension or a combination of both . . .
Praxichys - 20-1-2016 at 07:52
Try it with some soap in the water. XeonTheMGPony - 20-1-2016 at 07:58
As others said need some surficant, bit of isopropyle, or soap.Fulmen - 20-1-2016 at 08:31
I doubt viscosity is the answer as it should only decrease flow rates. Surface tension is far more likely, I assume it's the same effect that causes
wet fabrics to trap air. Metallus - 20-1-2016 at 08:34
Tomorrow I'll try with the dry sieve and then I'll wet it again and try adding some soap and see if this happens again.
By the way, this is not exactly a "problem", but more like a curiosity of mine. I was just surprised that no matter how much I pressed the sieve, the
air trapped inside wouldn't come out of the pores.
If I dip the sieve midway (If I don't totally drown it in water), I can see through holes and it is clearly devoid of water (Besides, I can see the
water level rise noticeably), which makes me think that there is either no water at all on the surface of the grit or that it is such a thin layer
that it's invisible to the naked eye.
Praxichys - 21-1-2016 at 07:34
The next step is to make a screen door for a submarine.
Bubble Point Pressure
careysub - 21-1-2016 at 11:29
It is due to surface tension, and here is a page that will permit you to calculate the pressure required to force the water through the screen:
This is used as a means of measuring screen pore sizes.
Oh yes, it makes sense, thank you.
I didn't know this was actually used to determine pore size, interesting indeed. Thankschemrox - 29-1-2016 at 16:26
be damned careful sonicating porous glass filters. I sonicated a fine filter in NaOH/MeOH/H2O solution and it broke up the filter. Fucking
disintegrated it. It wasn't in that long either. It only happened once but I have stopped using strong base when cleaning them in the sonic bath since
that occurred.Metallus - 5-2-2016 at 09:19
be damned careful sonicating porous glass filters. I sonicated a fine filter in NaOH/MeOH/H2O solution and it broke up the filter. Fucking
disintegrated it. It wasn't in that long either. It only happened once but I have stopped using strong base when cleaning them in the sonic bath since
that occurred.
The ones I use are made of aluminium and I usually sonicate them in water, so it shouldn't be an issue.
However, I'll pay attention if I'll ever use a glass filter, thanks for the prompt.
if it's viscosity
trapping the air or is it surface tension or a combination of both . . .