Search |
[Next Page] |
Unconventional Shaped Charges Yes the idea that you can actually catch something that penetrates steel with relatively soft materi ... |
14-8-2015 at 03:15 by: greenlight |
First recovery no-go Okay, so the first recovery system went not so well.
Even though a hand level and laser pointer was ... |
14-8-2015 at 01:20 by: greenlight |
Unconventional Shaped Charges I am hoping nothing causes it to stray, but thanks I will post results as soon as I can |
13-8-2015 at 18:19 by: greenlight |
Unconventional Shaped Charges I will do my best to get the pipes straight using a level and will aim EFP using a laser pointer.
I ... |
13-8-2015 at 09:59 by: greenlight |
Soft recovery system Projectile recovery system ready to test.
There is a 1 meter pipe filled with packing styrofoam, a ... |
13-8-2015 at 07:20 by: greenlight |
Unconventional Shaped Charges I drew a quick sketch of your liner and my liner to scale with a mm ruler.
I think it would work be ... |
13-8-2015 at 01:33 by: greenlight |
Unconventional Shaped Charges How many mm deep is your depth of curvature (the lowest point in the curve of the liner) nux?
|
12-8-2015 at 22:20 by: greenlight |
Unconventional Shaped Charges Thats a nice result for 5 grams of PE and a 10 mm target.
My PE is the same when I mix the binder ... |
12-8-2015 at 02:49 by: greenlight |
Unconventional Shaped Charges Yes that's pretty much exact design except there was no powder charge in there. The entire charge w ... |
11-8-2015 at 18:31 by: greenlight |
Unconventional Shaped Charges If you mean the depth of curvature of the liner it was 5 mm (16.6% of liner diameter). |
11-8-2015 at 07:44 by: greenlight |
Unconventional Shaped Charges Thankyou..
I was thinking of using a 2 metre long pipe filled with sawdust and another 1 metre long ... |
11-8-2015 at 04:53 by: greenlight |
Unconventional Shaped Charges I think that the speed the slug is travelling will cause it to deform still.
There is a test I foun ... |
10-8-2015 at 06:09 by: greenlight |
Unconventional Shaped Charges I had the plate against a tree but it penetrated just to the left of it it so I couldn't retrieve it ... |
10-8-2015 at 05:36 by: greenlight |
Unconventional Shaped Charges Yes it did haha..
Standoff was 60 cm exactly.
[Edited on 10-8-2015 by greenlight] |
10-8-2015 at 04:55 by: greenlight |
Unconventional Shaped Charges Yes, much better effect than before.
I think I will see if it can penetrate 3/4 inch steel next. |
10-8-2015 at 04:26 by: greenlight |
EFP IMPROVEMENT I performed another test with an EFP trying to drop the amount of explosive used and use PE instead ... |
10-8-2015 at 03:01 by: greenlight |
Plasticiser question. Ah, yes maybe white spirits could work as well if you have it in your country as it isn't carcinogen ... |
10-8-2015 at 02:49 by: greenlight |
Plasticiser question. I'm pretty sure Dioctyl sebacate is used in C4 with Polysobutylene and Semtex has a different mix of ... |
10-8-2015 at 00:08 by: greenlight |
Plasticiser question. I think it is fine with the 15% binder, even though it is not all binder, the commercial Semtex has ... |
9-8-2015 at 21:45 by: greenlight |
Plasticiser question. Your going to need at least 10-12% bare minimum using just PB on its own and it has to be rolled int ... |
8-8-2015 at 21:46 by: greenlight |
PETN recrystallisation procedure for LOW density I always use that procedure and get a nice mix of fluffy powder/granules. Good to plasticize.
Mayb ... |
8-8-2015 at 09:16 by: greenlight |
PETN recrystallisation procedure for LOW density That tooling looks awesome Nux, I have been looking for a former like that for conical shaped charge ... |
7-8-2015 at 02:29 by: greenlight |
PETN recrystallisation procedure for LOW density Yeah it is about the same consistency as clear silicon and very sticky and tacky and never dries.
Y ... |
6-8-2015 at 05:51 by: greenlight |
PETN recrystallisation procedure for LOW density I can't get the bird repellent here either i searched many hardware and garden stores after Neonpuls ... |
6-8-2015 at 03:39 by: greenlight |
PETN recrystallisation procedure for LOW density What are you using for the PB?
Is it bird repellant?
Are you plasticizing PETN or ETN? |
6-8-2015 at 02:38 by: greenlight |
[Next Page] |