| Search |
| [Next Page] |
Energy Injected to the Wire During the First Current Pulse
The following snip-it and table were taken from, "Electric Explosion of Wires as a Method for Prepar ... |
18-4-2015 at 14:10
by: Hennig Brand |
Has anyone made a EBW setup.
Interesting ideas. I can see the third one working, but I think it would be very difficult for most ... |
17-4-2015 at 18:37
by: Hennig Brand |
0.3g of ETN Initiated With 40 Gauge Copper EBW
[b]EBW Head:[/b]
A half inch or so of hot melt glue stick was sliced off on a cutting board, dril ... |
17-4-2015 at 15:12
by: Hennig Brand |
Has anyone made a EBW setup.
The bug zappers have a tiny flyback transformer in them, which produces AC, but the output is rectif ... |
17-4-2015 at 13:56
by: Hennig Brand |
Has anyone made a EBW setup.
I think the bridgewire should be up on posts with low density fine secondary explosive all around it ... |
16-4-2015 at 16:28
by: Hennig Brand |
Has anyone made a EBW setup.
Unless you are going to replace the capacitor bank and main high voltage & high current switch w ... |
15-4-2015 at 16:31
by: Hennig Brand |
Is old picric acid gauze found in first aid kits really that dangerous?
I would need to dig for a reference, but it seems to me that there was work done with lead picrate o ... |
15-4-2015 at 14:42
by: Hennig Brand |
Has anyone made a EBW setup.
Interesting, it should work fine then. I have seen the same thing done with stunguns, which is where ... |
15-4-2015 at 14:36
by: Hennig Brand |
Simple Trigatron Trigger Pulse Generator From Bug Zapper Power Supply
Yeah, I knew you meant Cooper. Thanks for that compressed file, it has a lot of good stuff in it. I ... |
15-4-2015 at 02:50
by: Hennig Brand |
SM EM Research Project - Calling for EM Research Junkies
I agree, for instance high velocity explosives are needed to efficiently cut steel and while they d ... |
14-4-2015 at 05:41
by: Hennig Brand |
Screw Triggered Spark Gap
Thanks, that site looks interesting. There are also at least a few sites online with peoples' descri ... |
13-4-2015 at 13:15
by: Hennig Brand |
Triggered Spark Gap Switch
From the little bit I have learned about it so far, trigatrons appears to be much more controllable, ... |
12-4-2015 at 04:54
by: Hennig Brand |
NPED detonator
Rosco, are you stirring the pot again?  I am completely sane......I think.
I also think that ... |
11-4-2015 at 08:10
by: Hennig Brand |
High Voltage/High Current Relay
This relay which I built in the last hour or two is extremely crude, but something much more refined ... |
11-4-2015 at 07:10
by: Hennig Brand |
NPED detonator
Sounds like it could work, Bert, and it does solve the gravity issue. |
10-4-2015 at 09:32
by: Hennig Brand |
NPED detonator
Good that you got the lead in there. I think lead is the key to success. 
It is likely normal ... |
10-4-2015 at 08:53
by: Hennig Brand |
Has anyone made a EBW setup.
Looks very nice. Is that an EBW power supply?
Also, forgot to mention that there were high ohmic ... |
10-4-2015 at 06:11
by: Hennig Brand |
Unconventional Shaped Charges
Less inert binder will of course make an explosive with higher performance, but then it will not be ... |
9-4-2015 at 18:44
by: Hennig Brand |
NPED detonator
He is referring to a post of his made on that date and time in this thread. Last page of this thread ... |
9-4-2015 at 16:10
by: Hennig Brand |
Has anyone made a EBW setup.
Thanks, not a bad idea. You know though, the two series connected bug zappers have no problem chargi ... |
9-4-2015 at 14:27
by: Hennig Brand |
24uF Capacitor Charged To 1600V Discharged Through 12ft RG6 Coax Into 40 Gauge Copper Bridgewire Initiates ETN
I hooked up the big 2kV, 24uF capacitor this morning to the bug zapper HV power supply. A 40 gauge c ... |
9-4-2015 at 06:55
by: Hennig Brand |
NPED detonator
There may be a certain temperature, or range of temperatures, that works best to initiate the ETN or ... |
9-4-2015 at 04:31
by: Hennig Brand |
NPED detonator
[rquote=400216&tid=24817&author=Laboratory of Liptakov]This is very interesting. Dripping le ... |
8-4-2015 at 16:12
by: Hennig Brand |
EBW HV Power Supply from Handheld Bug Zapper Rackets
I have two hand held bug zappers that were given to me which had mechanical problems of some sort bu ... |
8-4-2015 at 14:50
by: Hennig Brand |
Thermal Shock Initiation Using Molten Metal
Was doing some soldering today and out of curiosity I dropped little blobs of molten 60-40 solder on ... |
7-4-2015 at 13:54
by: Hennig Brand |
| [Next Page] |
